Mini Mr.BulletFeeder by DAA - Rifle
$109.00
Qty.:
Add to Cart
Tell a Friend
Send

Available options:

Caliber  x

Would you like to add:

Mini Mr.BulletFeeder by DAA - 6-tube Magazine - Rifle
Mini Mr.BulletFeeder by DAA - 6-tube Magazine - Rifle  x
Manufacturer: Double-Alpha Academy
  • TIM YAWN
    Date Added: Sunday 18 March, 2018
    This is the only way to go when it comes to bullet feeders. I tried the Hornady dies first and they are more work than not having one. These are just put it in and go. Great product.
    Rating: (5 of 5 Stars!)
  • Juraj
    Date Added: Wednesday 14 February, 2018
    this purchase was my first disappointment with DAA because two of the six tubes have their diameter so small that 55 grain bullets get stuck in them and it is quite challenging to get them out
    Rating: (3 of 5 Stars!)
  • Scott
    Date Added: Friday 26 January, 2018
    Excellent product but could use a minor improvement. The feeder does not have positive fit between the cassette and feeder die. I had to put a small piece of masking tape on the die to give it a firm fit. On the QC side, there were plastic shavings from when the tubes were cut stuck in the tubes. Nothing a quick blast from the air compressor couldn’t fix, but should have been taken care of during mfg.
    Rating: (4 of 5 Stars!)
  • randy walsh
    Date Added: Friday 05 January, 2018
    I have two loadmasters and a 9mm.223,308 mini mr. bulletfeeder.It makes reloading a breese.
    Rating: (5 of 5 Stars!)
  • Robert Dake
    Date Added: Friday 22 December, 2017
    installed it on my Dillon 550 in seconds, doubled my reloading output. only draw back is it only holds 72 .30 bullets
    Rating: (5 of 5 Stars!)
  • Brian
    Date Added: Thursday 30 November, 2017
    Great product for the money! Well made with quality materials. So far over 3,000 .223 and zero failures. Kind of a pain to load the tubes, but at less than a 1/3 of the cost for the automatic feeder for my Hornady, I can't complain, Can only load 100 primers at a time anyway, haha. Lightning fast shipping.
    Rating: (5 of 5 Stars!)
  • Robert Bardoorian
    Date Added: Thursday 16 November, 2017
    I bought the 45&308 first and they worked so well I got 223&38 as well All are on two Dillon 650s and it is actually fun reloading now! Bob Bardoorian
    Rating: (5 of 5 Stars!)
  • Mr. Endurance
    Date Added: Friday 10 November, 2017
    Hands down the best setup I've used. I have several Hornady feeder dies and what a difference. I wish that I had never bought anything but the DAA feeder. Setup was under 5 minutes their was zero tweaking and BT bullets never fall off the cases once loaded. ***** 5 STARS *****
    Rating: (5 of 5 Stars!)
  • Eric
    Date Added: Wednesday 06 September, 2017
    Simple but a great addition to the reloading process. While some have an issue with the feeder assembly price, I think the engineering and quality of the feeder justifies the cost. Also, one must consider the market for this type of unit, I doubt the company is cranking out thousands of these things every hour. When adjusted properly, the feeder functions virtually without fail. Presently I use it on a Dillon s1050 with certain plated 9mm bullet profiles that the automatic Mr Bulletfeeder unit has a hard time flipping to the correct feed position.
    Rating: (5 of 5 Stars!)
  • Barry Silberman
    Date Added: Sunday 06 August, 2017
    The Mini Mr. Bullet Feeder is an excellent concept. Reasonably priced and works exactly as described. I now use them for 9MM, 45 ACP and 223. Double Alpha's Customer Service is also outstanding. I had a couple of questions and received a response within an hour. Great products. Great service.
    Rating: (5 of 5 Stars!)

Mini Mr.BulletFeeder by DAA - Rifle

Reviews: 4.7 of 5 Stars!(Current Reviews: 4.722)

The Rifle Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 70-100 bullets, depending on bullet caliber and length. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder. 

 

Using a Bulletfeeder while reloading is a real pleasure. It makes the reloading process faster and much easier. If you have never used one, you are missing out on one of the greatest reloading assists out there! A Bulletfeeder also improves safety, by preventing the need to insert your fingers under the tool head to place your bullets on the brass. Everyone should use one! 

 

Each magazine of bullet tubes needs to be filled by hand before reloading, much in the same way you would fill your primer tubes before starting your reloading session. With a little practice, it will take you about 2 minutes to fill the tube assembly. And this can be done in advance while watching TV in the comfort of your living room. Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting your reloading session. 

 

While reloading, you will see the bullets drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue without delay. 

 

The Mini Mr.Bulletfeeder can be used on any progressive reloading machine which uses the same size dies as Dillon. Be aware that the bullet feeder does require a station in your tool head, directly after the powder dropper. 

 

We have found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to do with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050. 

 

Your Rifle Mini Mr.Bulletfeeder by DAA includes:

1 x 6-Tube Bullet Magazine Assembly

1 x Dropper Die Assembly

3 x Spare Steel Ball-Bearings for Dropper

1 x User Instruction Sheet 

 

No expanding powder funnel is included with this system, because throating the rifle brass in the powder funnel is not possible. That would lead to too small a powder through hole. Flaring the brass must be done as a prep stage or using a modified M-die on the 1050.

Showing: 1 - 5 of 22
Mini Mr.BulletFeeder by DAA - Rifle
TIM YAWN
Date Added: Sunday 18 March, 2018
This is the only way to go when it comes to bullet feeders. I tried the Hornady dies first and they are more work than not having one. These are just put it in and go. Great product.
Rating: (5 of 5 Stars!)
Mini Mr.BulletFeeder by DAA - Rifle
Juraj
Date Added: Wednesday 14 February, 2018
this purchase was my first disappointment with DAA because two of the six tubes have their diameter so small that 55 grain bullets get stuck in them and it is quite challenging to get them out
Rating: (3 of 5 Stars!)
Mini Mr.BulletFeeder by DAA - Rifle
Scott
Date Added: Friday 26 January, 2018
Excellent product but could use a minor improvement. The feeder does not have positive fit between the cassette and feeder die. I had to put a small piece of masking tape on the die to give it a firm fit. On the QC side, there were plastic shavings from when the tubes were cut stuck in the tubes. Nothing a quick blast from the air compressor couldn’t fix, but should have been taken care of during mfg.
Rating: (4 of 5 Stars!)
Mini Mr.BulletFeeder by DAA - Rifle
randy walsh
Date Added: Friday 05 January, 2018
I have two loadmasters and a 9mm.223,308 mini mr. bulletfeeder.It makes reloading a breese.
Rating: (5 of 5 Stars!)
Mini Mr.BulletFeeder by DAA - Rifle
Robert Dake
Date Added: Friday 22 December, 2017
installed it on my Dillon 550 in seconds, doubled my reloading output. only draw back is it only holds 72 .30 bullets
Rating: (5 of 5 Stars!)
Showing: 1 - 5 of 22

Mini Mr.BulletFeeder by DAA - Rifle

Full Name:
E-Mail Address:
Telephone Number
Country
Enquiry:
Alpha Dynamics USA
2908 Betz Court, Orefield, PA 18069
Phone: (888) 628-3233 or (610) 366-9752
Fax: (610) 366-9680
E-mail: sales(at)doublealpha.biz