Sunday 17 July, 2022
Better than the Dillon hex key holder. Seems sturdy. Easy to install.
Robert S***s
Saturday 06 February, 2021
I like the matte and smooth finish, it looks great and it holds all the tools I need. The magnetic side is very smart and useful. The only thing I don’t really like is the mount system, it doesn’t keep the tool-holder in position very well, I had to add some tape to keep it from moving around too much
Fabio N***s
Thursday 21 January, 2021
received my tool holder for my dillon xl750,puy it on and the tightened the screw ,then put my most used tools on it and it would fall down as i would use my press, ,easy fix ..What i did was put it back in place where i wanted it ,then i put a small zip tie around the case feeder pole underneath the tightened part..works great now..doesn't move..still a good product..thanks Double Alpha
Ronald H***p
Sunday 20 September, 2020
I was really looking forward to getting this to keep the common used tools at hand. I wasn't too put off by the fact that the included screws are not the same size as the tools that are included (as mentioned in other reviews)... but I can overlook that (even though it only makes sense that Tab A should fit Slot A).
My biggest gripe on this is the way that it mounts to the vertical tube. The material is pliable enough that when you tighten the screws, the side opposite really do not tighten around the tube. Even when tightened as much as it can be (which is only so much, because the captive nuts spin), the holder can still spin and fall down the tube.
My next gripe is one of the holes for the hex key isn't large enough so it sits above all the others.
DAA reply:
Hi Brian,
You are right about the keys not fitting the screw in the product itself We will consider changing that for the next run. We always use Metric Screws in Europe, and the key set (which is a separate product by the way, are all Inch keys for the Dillon press).
Tool holder sliding: try to turn the spacer piece upside-down, inserting it from below. that will grip tighter. If not enough, one layer of black electric type around the pole where you wish to position it will surely prevent it sliding.
If one of your tool holes seems small, it is probably due to the rubber coating on that key being too thick. That rubber dip process is not very precise for thickness. Cut away a little of the rubber coating, and your key should seat like all the others.
Bryan R***s
Sunday 30 August, 2020
Mounted it to my Dillon XL750 casefeeder pole. After finding the proper spot I now have my often used tools at hand.
Not that I am adjusting the press constantly, but it saves you time looking for the default tools.
Alwin de B***n
Wednesday 29 July, 2020
Works like it is supposed too. Mounts out of the way and is easily accessible. Like the magnetic side to allow use of placing items there. That was a plus.
Keith B***y
Friday 10 April, 2020
This is a well designed accessory for your press. I own several M7 Revolutions and was looking to organize the many Hex Key tools required to work/use the press. I was able to get all the needed Hex Keys in the tool holder...(I'm using my own Hex Keys w/o rubber coated elbows)...some keys needed to share the same slot...(no big deal). I was also able to add a pair of long nose tweezers, a set of small adjustable wrenches (for Mighty Armory Decapping pin & rod flats), a Sharpie and a Philips Head (#2) screwdriver. I'm happy...
The only drawback is the diameter of the mounting bracket (round insert) is not large enough to wrap perfectly around the M7 Case Feed pole. It still worked, but not as slick as I had hoped for...but, I kinda knew this going into the purchase. Like I said, it works just fine...I would purchase again!
Mark W***n
Tuesday 07 April, 2020
Der Werkzeughalter fuktioniert sehr gut. Er Lässt sich leicht montieren. und ist drehbar-Top Tip: Mm ein Rutschen nach unten am Casefeeder zu verhindern, befestigen Sie am Besten unterhalb eine simple Schlachschelle.
Klaus W***r
Monday 04 November, 2019
This is a great add on for Dillon presses. It holds all the needed hex keys and wrenches to adjust the press, bullet feeder, and make caliber conversions with a great place to store in a most convenient way so the tools are not lost or make a clutter on your reloading bench. As with all Doublealpha products this product is well thought out and solidly built to give years of helpful service to the operator.
Joe C***n