Tuesday 07 March, 2023
I use two on my RL1100 with Mark 7 drive loading 9mm. One between powder drop and bullet drop the other between bullet drop and seating. If and when I have a problem with my setup it almost always happens in these two stages. This little brush completely solved the wobble in the cases during indexing. If you have a similar setup buy this product you won't be sorry. Thanks Double Alpha for another great product.
Friday 16 September, 2022
seems to work fine. just another little addition to make life easery
Monday 14 February, 2022
Works perfectly on an 1100 between hopper/bullet feeder to keep powder spill contained, or even between bullet feeder and bullet seating die to help prevent bullet from tipping over.
Tuesday 01 February, 2022
It needs to be trimmed but it works well. The pin broke of on so I drilled it out put in a screw.
Tuesday 01 February, 2022
A little expensive for what it does, but does seem to dampen down the cases on my XL750.
Thursday 07 October, 2021
Bought 2 of these thinking they would help. After lots of trimming and more trimming and more trimming never got it to work without stopping the index plate short of position. Never even bothered with the second one. Seemed more trouble and expensive than it was worth.
Went with guides instead and is trouble free.
Monday 20 September, 2021
I got 2 of the Psp Brushs for the dillon Xl750 thinking that I would need them as plate rotated around from the powder feed to bullet seating but in the end only needed one from the powder feed to powder checker as the dillon is so smooth :)
they do work as the 9mm case is full and it keeps the powder in it
Saturday 24 April, 2021
this works great in helping keep powder from spilling out. It keeps the case steady when advancing to the next station.
Thursday 15 April, 2021
Works great! Thank You for providing a product that although is small in size, it fills a niche in the powder shortcoming of a press.
Tuesday 09 March, 2021
Works great, no spilled powder anymore when reloading 9mm.
Roel van der S***r
Thursday 04 March, 2021
Once I figured out what station to put this in it worked great. No more spilled powder.
Sunday 28 February, 2021
Now why didn't I think of that? I have only loaded a couple hundred rounds with it and it seems great. May have to trim it up a little but not yet. I highly recommend it and I would buy it again. Alex Ragulsky
Saturday 27 February, 2021
Simple yet amazing! It flat out WORKS! I had to modify it a little to clear the LED strip on my press, but that's not the PSP's fault. I am amazed at the way it works. Get you one!
Sunday 14 February, 2021
Installed the DAA PSP brush on my RL1100 and it made a great machine better, spills are gone and machine stays a lot cleaner. Get one and try it, you won't be disappointed.
Saturday 06 February, 2021
Nice little addition to my Dillon 750XL. I reload 9mm and it works very well, stabilizing the cases during indexing. No trim or modifications required on my case, it just works
Tuesday 24 November, 2020
Like others, I had to give this brush a shave to keep it from tilting the cases so much that they sometimes would catch in the die. Other than that, it does help to minimize case shake.
What was also a big help for me was to trim a bit off of the spring that applies pressure to the indent ball under the shellplate of my Dillon 1100 press. That made the shellplate stop at each station with just a bit less whomp. Between that trick and this brush, I don't have nearly the messy press I used to.
Check uTube for the spring trimming video. . . you should probably have a spare spring on hand in case you get too enthusiastic :).
Monday 23 November, 2020
Haven’t had a chance to use it yet still waiting for press to come in
Wednesday 16 September, 2020
Due to the brush and its location it will slowdown the filled shell and not tilt the bullet, this helps in faster reloading and less failures. A well spend investment.
Sunday 19 July, 2020
It works. However the plastic pin keeps breaking I'm on my second and probably the last one.
Fernando E M***a
Sunday 31 May, 2020
Gekocht na het lezen van de reviews hier maar ik kan niet geloven dat iedereen zo positief is na zelf deze DAA PSP Brush gebruikt te hebben.
Na 500 9mm patronen op een XL650 was de borstel al helemaal uitgelubberd en alle haren aan de voorkant staan omhoog wat tot gevolg heeft dat het niet doet wat het hoort te doen namelijk onregelmatige kruitladingen cq verspilling tegen te gaan.
Een ander probleem is dat de complete borstel ook steeds omhoog kruipt het blijft gewoon niet op zijn plek zetten je moet het telkens naar beneden duwen.
Ik kan deze DAA PSP Brush niet echt aanbevelen het is weggegooid geld en hoort ook niet thuis op deze prima webwinkel.
DAA: sorry to read of your poor experience. that is odd as most are very happy with the product. We will contact you privately to work something out.
Mario van der V***n