In stock
$16.95
Reward Points
Each product you purchase earns you a certain amount of Reward Points (each Reward Point equals to a Dollar/Euro amount) which you can use on your next purchase.
Once you have accumulated some Reward Points you can choose to use it on your next purchase or keep saving it.
To use your Reward Points make sure you input the amount you wish to use (from your total accumulated amount) at the checkout process.
Reward Points cannot be transferred to another user and expire in 12 months unless new points are accumulated prior to the 12 month expiration date in which case the 12 months period resets.
The Reward Points are available to you for any future purchase on the DAA webshop.
Choose options
We Also Recommend

Latest reviews

Saturday 02 September, 2023
This should be included with the bullet feeder when you first buy it. Just turn a couple of screws and you all set. Buy one of these and throw the spacers in the garbage.
Rating: (5 of 5 Stars!)
Monday 28 August, 2023
Much easier and better than the original system that goes with the Bulletfeeder! Good instructional video by Saul!
Rating: (5 of 5 Stars!)
Thursday 24 August, 2023
This works perfectly. Once set up, it flawlessly performs. I would recommend this for anyone using a Mr. Bullet Feed.
Rating: (5 of 5 Stars!)
Monday 21 August, 2023
Absolutely a must-have. This is the biggest improvement to the MBF unit.
Rating: (5 of 5 Stars!)
Wednesday 09 August, 2023
This item is a cure for a sometimes frustrating problem.
I purchased two of them one for short bullets and one for long ones.
This is the slickest little thing. It’s very easy to set up and makes my life much easier.
I have virtually no outside down bullets anymore.
Another outstanding...
Rating: (5 of 5 Stars!)
Wednesday 19 July, 2023
When I purchased the Mr. Bullet Feeder for 9mm I had envisioned using it for the multiple other calibers I reload for as well. However after the setup and fiddling with the shims and spacers to get it to feed smoothly, I was reluctant to change over to another caliber as I didn't want to have to...
Rating: (5 of 5 Stars!)
Monday 13 March, 2023
Purchased one initially and found this to be by far the easiest way to adjust for different bullet lengths. No more add/subtract shims and having to keep up with them. Ultimately purchased the 3 pack and no a change over is just slide the appropriate nose guide in place and you are done. At least...
Rating: (5 of 5 Stars!)
Monday 30 January, 2023
Well this is just a fantastic bit of kit. My bullet supply is a little dry at the minute and I'll buy what I can get my hands on. This meant constant fiddling with spacers and I still wouldve got the odd upside down head. Not any more! This is a great upgrade to Mr Bullet Feeder and allows me to...
Rating: (5 of 5 Stars!)
Friday 27 January, 2023
If you have an older Mr. BulletFeeder then its totally useless. You'll have to do more than a little fitting. One screw hole on the back of it is totally covered so you have to remove the screw for it to even slide in and the clicker thing gets jammed on it as well since this new nose guide is...
Rating: (1 of 5 Stars!)

Mr.BulletFeeder Pre-Set Nose-Guide

(9)
Manufacturers: Double-Alpha Academy

Description:

Save setup time and make caliber swap-overs easier than ever, with the Mr.Bullet Feeder Pre-Set Nose-Guide!                              

Those familiar with using the Mr. Bullet Feeder by DAA, will know how critical it is to adjust the Nose-Guide piece precisely correctly for the bullet caliber and profile you are collating. Positioning the Nose-Guide at precisely the correct depth under the collator bullet plate, and setting the depth of the Nose-Guide pocket just right, are key to collating with 100% reliability and to feeling all bullets base down as required.

If you often switch between bullet types or calibers, it can be time consuming to have to readjust that nose guide each time.

Well – no more! 

The Mr.Bulletfeeder Pre-Set Nose-Guide allows you to micro-adjustment the position of the Nose Guide and quickly achieve the perfect setting for your bullet type and caliber. And no more need for the loose Nose-Guide Spacers either, which so often got lost between caliber change overs. Now the depth of the pocket is adjusted with just a turn of a screw.

And better still! If you have multiple Pre-Set Nose-Guides, you can remove each one pre-set for a particular bullet – and drop it back in next time you need it! The part snaps into place against the magnetic stop-position piece (included) and you are perfectly setup and ready to load. This enables you to change bullet types in seconds, not minutes. 

The bright colored orange material is perfect for writing on with a black Sharpie, to mark the bullet type it is pre-set for.

Please note:

This Pre-Set Nose-Guide is a drop on fit to all the Mr.BF units produced from 2018 and later (the units which have the hanger that clamps onto the motor gear box). Earlier models – the ones which had the round aluminum rods and round Delrin puck hangers – will require some DIY fitting. You can still use this new part – but you will need to slightly widen the slot for the Nose-Guide in your Collator base before use, and modify the shape of the magnet holder piece to fit next to the round mounting rod on the base plate.

Will not fit the MBF Pro.

Watch the tutorial video for installation instructions.

Reviews (9)

Saturday 02 September, 2023
This should be included with the bullet feeder when you first buy it. Just turn a couple of screws and you all set. Buy one of these and throw the spacers in the garbage.
Monday 28 August, 2023
Much easier and better than the original system that goes with the Bulletfeeder! Good instructional video by Saul!
Thursday 24 August, 2023
This works perfectly. Once set up, it flawlessly performs. I would recommend this for anyone using a Mr. Bullet Feed.
Monday 21 August, 2023
Absolutely a must-have. This is the biggest improvement to the MBF unit.
Wednesday 09 August, 2023
This item is a cure for a sometimes frustrating problem.
I purchased two of them one for short bullets and one for long ones.
This is the slickest little thing. It’s very easy to set up and makes my life much easier.
I have virtually no outside down bullets anymore.
Another outstanding product from Double Alpha
Wednesday 19 July, 2023
When I purchased the Mr. Bullet Feeder for 9mm I had envisioned using it for the multiple other calibers I reload for as well. However after the setup and fiddling with the shims and spacers to get it to feed smoothly, I was reluctant to change over to another caliber as I didn't want to have to re-do all of the work getting the 9mm to feed right. The Pre-Set nose guide solves that problem by allowing you to set all of the parameters for a bullet type and then slide it out and slide in a new one for a different bullet type and or caliber. This invention has opened the door to using the Mr. Bullet Feeder for all of the calibers and bullet types I use. Well done!
Monday 13 March, 2023
Purchased one initially and found this to be by far the easiest way to adjust for different bullet lengths. No more add/subtract shims and having to keep up with them. Ultimately purchased the 3 pack and no a change over is just slide the appropriate nose guide in place and you are done. At least one should be included with original purchase. Highly recommended.
Monday 30 January, 2023
Well this is just a fantastic bit of kit. My bullet supply is a little dry at the minute and I'll buy what I can get my hands on. This meant constant fiddling with spacers and I still wouldve got the odd upside down head. Not any more! This is a great upgrade to Mr Bullet Feeder and allows me to make minor tweaks with a turn of a screw or two.

They're cheap enough to have a few for different calibres so I'll be picking up a couple more with my next order.
Friday 27 January, 2023
If you have an older Mr. BulletFeeder then its totally useless. You'll have to do more than a little fitting. One screw hole on the back of it is totally covered so you have to remove the screw for it to even slide in and the clicker thing gets jammed on it as well since this new nose guide is too high. That means you'll have to do considerable mods to your feeder to make it fit. Bottom line is unless you have a newer model and they guarantee that it will fit and work for the one you have, don't waste your time or money on it.

Also Available In Set(s)

You may also be interested in