Shopping Cart
0 item(s) - €0.00

SUPPORT SYSTEM

Race Master / Alpha-X Insert Block Assembly (Magnetic)Race Master / Alpha-X Insert Block Assembly (Magnetic)
Race Master / Alpha-X Insert Block Assembly (Magnetic)
Models and Fitting

Q: I have one of the newer Sig X5 models. Will the Sig X5 insert block fir the new model?

A:, yes it will. In fact, we tested the new Sig X5 and X6 models and they all fit to the X5 insert block.

Race Master Holster (Magnetic)Race Master Holster (Magnetic)
Race Master Holster (Magnetic)
General questions

Q. Will the Glock insert fit all Glock models?
Yes and no. Not trying to be evasive, but here’s the deal: The RM holster requires a very precise fit to the trigger guard of the gun. We have found that amongst the various Glock models, and sometimes even in the same model, with various generations of molds, there are slight variations in the trigger guard dimensions. Our only option was to keep the dimensions tight, to fit the smallest Glock trigger guard we could...

Function

Q. What kinds of belts can I fit the RM holster to?
The belt holder is designed to accommodate belts up to 39mm (1.5”) wide. All belts in this category may be used. We have tried the holster on the DAA belts, CR speed, H&S and a few others. The retention plates at the back can be screwed down to grip tightly even thinner belts, so the holster can be held solidly. 2” belts cannot be used, unless you cut out a piece from the belt, narrowing it down to...

Setup

How to assemble your hoslter

The holster is designed for use on dedicated shooting belts, which are rigid and of solid construction. (DAA Competition Belts or similar).

Loosen or completely remove the four M4 round-cap screws which hold the two Belt-Hanger Retention Bars (1) in place, position the holster on your belt, and re-tighten the four screws. Do not
over-tighten!

If your shooting belt is much narrower than 1.5”, you may need to use...

Magnetic Insert

To dismantle the magnetic insert, follow these steps:

1. Remove the insert block from the holster by removing the two small M4 screws from the back of the holster

2. Using a punch and hammer, push the two steel pins from the front of the block towards the back (push from the side with the gun type engraved). These pins may be tight.

3. Once the pins are out, the plastic wedge holding the 2nd magnet will come out. Make sure the magnet does not fall...

Custom Fitting

Some shooters have experience a problem with their Race Master fit to their pistols. The following should help you resolve this:

First – check to see that the fit to the locking block is good. Remove the slide lock from within the block – and assemble the block into the holster without a slide lock. You will need to remove that long M3 screw from the back, and the slide lock will slide out upwards. Holster your gun and see that is slides in and out loosely. If not – you...

Gun specific questions

Q: I have a Sig Sauer x-six ppc with 9 mm and with a .22 barrel, as well I have a doctor mounted on the xmount, does the holster fit?

Yes to all fits, EXCEPT the X-mount insert will only be suitable for the X-Six with the X-mount installed. If you are to shoot this gun without the mount, please select an additional X5 insert.

Q: Would the Race Master fit the Tokyo Marui Hi-capa Airsoft pistol?

We do not have any insert that...

Maintenance and Care

Your new Race Master Holster is constructed of several precisely machined moving parts designed to work together and fit snugly to the trigger guard of your firearm. As with your firearm itself, every effort should be made to keep the holster well maintained, clean, and dust-free. Using a dust cover over your firearm and holster is a good practice that helps keep both your gun and holster clear and clean.

Periodically and more often in dusty conditions, remove and clean the Insert...

Various

Q. What kind of screws is used on the holster, and where can I get spares?
The screws used on the holster are all Metric, M3, M4, M5 and M6 stainless steel screws. All screws can be tightened using 3 hex keys, sizes 2.5, 3 and 4mm.
We will Shorty be offering a set of replacement screws as an accessory item, as well as hex key sets, as supplied with the holster.

Q. Is it possible to get custom logos or a name engraved on the holster body?